Friday, April 3, 2015

Chapter 17 (cont..3)- Check for One way shear in a Two way slab

Calculation of one way shear at the supports of a two way slab

We have seen the procedure for shear check in one way slabs. In one way slabs, the loads are transferred to two opposite walls. If the slab is subjected to uniformly distributed loads, then one half of the load will be transferred to one wall, and the other half will be transferred to the other opposite wall. But in the case of a two way slab, there are four walls, and the loads are transferred to all the four walls. If all these four walls are of equal length, then we can assume that, one fourth of the total uniformly distributed load will be transferred to each wall. But if the lengths are not equal, then the distribution of loads to each wall is complicated. In this situation, we can use the recommendation given by cl.24.5 of the code. According to this clause, the distribution of load on the short side is triangular, and the distribution of load on the long side is trapezoidal. This is shown in the fig.17.6 below:
Fig.17.6
Distribution of load in a two way slab
Right click and select open in new tab for an enlarged view
The portions that each wall will carry can be demarcated by drawing 45o lines from the corners. When these 45o lines are drawn from all the four corners, we will get a triangle (shown in blue color) at each short side, and a trapezium (shown in green color) at each long side. When the area is divided in this manner, the height of the triangles and the height of trapeziums will be the same, and is equal to half of the length of the short side.
We are designing a 1m wide strip of the slab. So the shear force will be maximum when the strips are taken at the apex point of the triangle and the trapezium. We need to consider any one only (triangle or trapezium) because the strip for both the cases are of the same length 0.5 lxn. where lxn is the clear span in the short direction. Also, we need not consider this whole length of 0.5 lxn. Only the load to the right of the critical section (which is at a distance of d, the effective depth of the slab, shown by the red dashed line in plan and section from the face of the support) need to be considered. This is because the shear force at the critical section will be caused by the loads acting on the right side of the section. This is shown in the section XX in the above fig.17.6
The area of the strip to the right side of critical section = (0.5 lxn – d) x 1 = (0.5 lxn – d) m2
So total factored load on this area is obtained as:
Eq.17.12
Vu = wu(0.5 lxn -d)
The rest of the procedure is same as that for a one way slab: The factored shear force Vu should be less than the shear contribution from concrete. The shear contribution from concrete is calculated as kτcbd. Where,
k is the modification factor given in cl.40.2.1.1 of the code, calculation of which we discussed in the case of one way slabs.
τc is the design shear strength of concrete, obtained from table 19 of the code,
b is the width of the strip of slab = 1000 mm, and
d is the average effective depth of the slab = (dx + dy)/2
Thus the procedure for shear check of a two way slab is complete.
Though we have had a somewhat lengthy discussion about the analysis and design of the simply supported two way slab, it can be summarized into just a very few steps:
(a) Determine the preliminary value of total thickness, and effective spans lx and ly as described in the previous section. lx is the shorter span, and ly is the longer span.
(b) Determine the factored load wu [Load factor x (sum of self wt., finishes and LL)]
(c) Calculate r = ly/lx
(d) based on r, calculate αx and αy
(e) Calculate the factored moments  Mux =  αx wu lx2  , and  Muy =  αy wu lx2   
(f) Provide the steel determined from Mux in the direction parallel to lx (in the bottom most layer) , and the steel determined from Muy in a direction parallel to ly.
(g) Do the shear check and also all other required checks that we do for a one way slab.
The solved example given below will illustrate all the points that we discussed above:
The reinforcement details according to the above design is shown in the figs.17.7,8 and 9 below:
Fig.17.7
Plan view
Plan view showing the reinforcement details of a simply supported two way slab
Fig.17.8
Section AA
Sectional view showing the reinforcement details of a simply supported two way slab
Fig.17.9
Section BB
We will now discuss the main features of the above figs:
The steel Ast,x is calculated from Mux. From Ast,x we fixed up #8 bars @ 140 mm c/c. This steel is laid parallel to lx. Consider the set of all the strips parallel to lx. That is., all the blue strips in fig.17.3. The strips in the middle region will require the steel Ast,x. But those on the sides, which are nearer to the shorter walls will be carrying lesser loads, and so they will not require the same Ast,x. For those strips, the spacing can be increased. But, as mentioned earlier, we assume that all the blue strips carry the same load, and so the same steel is provided for all the blue strips. Thus in the above fig.17.7, we can see that #8 @140 mm c/c is provided from the left short wall to the right short wall. Similarly, in the set of red strips parallel to ly in fig. 17.3, the strips nearer to the long walls will not require #8 @ 220mm c/c. For those strips, the spacing can be increased. But we assume that all the red strips carry the same load, and so the same steel is provided for all the red strips. Thus in the above fig.17.7, we can see that #8 @220 mm c/c is provided from the bottom long wall to the top long wall.
Now we will discuss another feature that can be seen in the above figs. Let us consider any one of the blue strips. It is simply supported on the two long walls. So the bending moment at the ends will be zero. So, like any simply supported member, the bending moment varies from a maximum at the middle of the strip to zero at the supports. Thus it is possible to curtail the bars. We have seen the details of curtailment here. For a simply supported two way slab we follow simplified rules of curtailment: The main bars are terminated at alternate ends, at a distance of 0.l from the face of the support. So 50% of the main bars are curtailed, and the other 50% continues into the support. We can see from the fig. that, this type of curtailment is done in both x and y directions.
The curtailed bars are not just stopped at 0.1l from the face of the support. They are given a 45o bend at that point, and thus they become top bars at the support. Thus we will get 50%  Ast as top bars at the supports. These top bars are necessary to resist any hogging moment that may develop at the supports.
In the next section we will see some basic details about torsionally restrained two way slabs.

PREVIOUS      CONTENTS       NEXT

             Copyright ©2015 limitstatelessons.blogspot.com- All Rights Reserved

Tuesday, March 24, 2015

Chapter 17 – Analysis and design of Two way slabs

At the beginning of Chapter 5- Analysis of One way slabs, we saw a presentation which describes the basic details about the behaviour of Simply supported slabs.  From the presentation, we get a clear understanding about the difference between a one way slab and a two way slab. When the distance ly increases, more and more load gets transferred in the other (x) direction, and the slab will become more like a one way slab. We have seen the limit beyond which we can design a slab supported on four sides as a one way slab: We take the ratio ly/lx. If this ratio is greater than 2, then we can design it as a one way slab even if it is supported on all the four sides. Here, it is important to note that ly  is the longer span, and  lx is the shorter span. This can be made clear based on the following fig.17.1:
Fig.17.1
Method of assigning lx and ly
Method of assigning lx and ly 
In the above fig., the part plan showing the slabs of a building is shown. For panel 1, the shorter span lx is horizontal and the longer span ly is vertical. But for panel 2, the shorter span lx is vertical and the longer span ly is horizontal. So we must not consider the conventional cartesian coordinate system while denoting the spans of a two way slab. Instead, we must follow the rule: Longer span is ly and shorter span is lx . Now we will see some more details about two way slabs:
In a one way slab, the slab is supported on two opposite walls. The loads will be transferred to these two walls only. But when the slab is supported on all the four sides, loads will be transferred to all the four walls. We can think of the total load acting on the slab, to be divided into two unequal shares. One share will be transferred in one direction, and the other share will be transferred in the perpendicular direction. If the slab is a perfect square, both the shares will be equal.
When a slab deflects into a cylindrical surface, there is curvature in one direction only. But when the slab deflects into a spherical surface, at any point on the surface, there is curvature in two mutually perpendicular directions. This means that all elements of the slab will experience a bending in two mutually perpendicular directions. So we must provide steel also in the two directions. The amount of steel that we have to provide in any one of these directions will depend on the bending moment in that direction. This bending moment in turn, will depend on the share of load in that direction. If the slab is a perfect square, then the bending moment in both the directions will be equal. So our next aim is to determine the share in each of the two mutually perpendicular directions.
Before we determine this, let us fix up the notations for the share in each direction, and also the bending moments in each direction. We have fixed up the notations for lx and ly based on the fig.17.1 Now we will consider fig.17.2 for loads and bending moments.
Fig.17.2
Notations for loads and bending moments
We can think about the bending of a two way slab in this way: The share which is transferred to the shorter walls bends the slab into a cylindrical shape. The share which is transferred to the longer walls also bends the slab into a similar cylindrical shape which is perpendicular to the first cylinder. The combined effect of these two cylindrical bends give the slab a spherical shape. Let us consider the two cylindrical bends separately as shown in the above fig.17.2. If wy was the only load present, and if the long walls were absent, then the slab will bend into a cylindrical shape, whose axis is perpendicular to ly. Similarly, If wx was the only load present, and if the short walls were absent, then the slab will bend into a cylindrical shape, whose axis is perpendicular to lx. Here wx and wy is the uniformly distributed loads over the whole area of the slab. As we will see in later sections, all portions of the slab will not experience the same uniform loads wx or wy. But for the ease of analysis, it is convenient to assume it as uniform, for a simply supported two way slab. Thus, from the two deflections shown separately, we can fix up the notations in an 'easy to remember' chart form:
● ly is the longer effective span, and lx is the shorter effective span
● The bending moment which makes the cylinder whose axis is perpendicular to ly is My, and the share which causes this Bending moment is  wy .
● The bending moment which makes the cylinder whose axis is perpendicular to lx is Mx, and the share which causes this Bending moment is wx.
Now we can proceed to determine the quantity of these shares. Let us divide the slab into strips parallel to lx and ly as shown in the fig. below:
Fig.17.3
Dividing the slab into strips
 
The red strips are parallel to ly and the blue strips are parallel to lx. The width of each of these strips is 1m. In the above fig., the strips are shown in two separate slabs. But actually, both the sets are to be considered in a single slab.
The chart that we prepared above, mentions about a cylinder whose axis is perpendicular to ly. It also mentions that the share that makes this cylinder is wy. Now, from the above fig.17.3, we can see that the cylinder whose axis is perpendicular to ly is made up of strips which are parallel to ly. So it follows that the share on each strip parallel to ly is wy. Similarly the share on each strip parallel to lx is wx. As mentioned earlier, wx and wy are not distributed uniformly over the whole area. So the load on strips also will not be uniform. Load on each strip will be different from the adjacent strip. We are assuming it to be uniform, for the ease of analysis.  We can add these two points to the above chart and make it complete:
● ly is the longer effective span, and lx is the shorter effective span
● The bending moment which makes the cylinder whose axis is perpendicular to ly is My, and the share which causes this Bending moment is  wy .
● The bending moment which makes the cylinder whose axis is perpendicular to lx is Mx, and the share which causes this Bending moment is wx.
● The share on each strip parallel to ly is wy
● The share on each strip parallel to lx is wx
For our discussion, we can take any one strip from each set as shown in the fig.17.4 below:
Fig.17.4
One strip from each set
 
The intersection of the two strips is shown in yellow color. So the yellow portion belongs to both the strips. From the lessons in Strength of materials, we know how to calculate the deflection of a beam at any point. We can consider the red strip and blue strip in the fig., separately. First consider the red strip. If we know the distance to the yellow portion from any of the short walls, we can calculate the deflection of the beam at that portion. Similarly, considering the blue strip, if we know the distance to the yellow portion from any of the long walls, we can calculate the deflection of the blue strip at that portion. The deflection calculated by considering the two different strips should be the same. This is because, which ever strip we consider, the yellow portion has been displaced by the same amount.
The above calculation will be a lot more easier, if we consider the yellow portion to be at the intersection of two ‘central’ strips. This is shown in the fig.17.5 below:
Fig.17.5
Intersection of two central strips
 
In this case, the yellow portion is at the midpoint of each of the strips. The expression for deflection calculation at the midpoint of a beam is a simple one. In the next section we will write this expression for each of the two strips.

PREVIOUS      CONTENTS     NEXT

             Copyright ©2015 limitstatelessons.blogspot.com - All Rights Reserved

Friday, March 20, 2015

Chapter 16 (cont..18)

The data available for load calculation are:
R = 150mm, T = 300mm, t= 190mm, wf,Data = 0.8 kN/m2, w LL,Data = 5 kN/m2,
Weight density of the brick masonry for steps = γs = 20 kN/m3
Loads on sloping portions:
(1) Self wt. of waist slab =
= 5.31 kN/m2
(2) Self wt. of steps =
Eq.16.5
0.5Rγs = 1.5 kN/m2
(3) Finishes = 0.8 kN/m2
(4) LL = 5 kN/m2
Total of the four items = 12.61 kN/m2Factored load (Load factor = 1.5) = 18.92 kN/m2
Loads on Landings:
(1) Self wt. of slab =
25t = 4.75 kN/m2
(2) Finishes = 0.8 kN/m2
(3) LL = 5 kN/m2
Total of the three items = 10.55 kN/m2Factored load (Load factor = 1.5) = 15.83 kN/m2
We have discussed the case of right angled stairs on the basis of fig.16.30 There we saw that only half of the load should be taken on the landing of such stairs. Here we have a similar situation. The landing at B is common to flights AB and BC. The load on this landing will contribute to the BM in both the flights. And also, both these flights are independent. That is., they have their own supports. None of them are supported on any landing.
The same situation is present at the landing at C. So we can see that at both the landings, only half the load (15.83 x 0.5 = 7.92 kN/m2) should be considered. Thus we can add loads to the line diagram in the previous fig.105, as shown below:
Fig.16.106
Line diagram showing the loads
Line diagram showing the loads

We can see that CD is the exact mirror image of AB. So we need to do the analysis and design of AB and BC only. The design of AB can be applied to CD also.
First we will analyse AB:
Eq.16.12:
 
The following data is available to us for using in the above equations:
w1 = 18.92 kN/m, w2 = 7.92 kN/m, l1 = 2.81 m, l2  = 1.36 m
So we get RA = 37.01 kN  and  RB = 26.93 kN
The Bending moment at any point at a distance x from the support A is given by:
Eq.16.13:
If we differentiate this equation, we will get the equation for the shear force at any point at a distance x from the support A:
Eq.16.14
The maximum bending moment occurs at a point where the shear force is equal to zero. So we equate the above equation 16.14 to zero and solve for x
Thus we get x = 1.96m from support A
Substituting this value in Eq.16.13, we get Maximum bending moment = 36.2 kNm
Thus we determined the reactions and bending moment in flight AB. Now we will analyse BC:
Reactions at supports B and C is given by
 
The following data is available to us for using in the above equations:
w1 = 18.92 kN/m, w2 = 7.92 kN/m, l1 = 1.2 m, l2  = 1.36m
So we get RB = RC = 22.12 kN
The maximum bending moment occurs at midspan and is given by
Eq.16.16
= 26.17 kNm.
Thus we determined the reactions and bending moment in flight BC also. So now we can design the steel and do the various checks. The design part is given as two separate pdf files the links of which are given below:
The reinforcement details according to the above designs are shown in figs.16.107,108 and 109 below:
Fig.16.107
Reinforcement details of flight AB
Fig.16.108
Reinforcement details of flight BC
Fig.16.109
Reinforcement details of flight CD
The bar diameters and their spacing in the last flight CD will be same as that of the first flight AB. But the bending of the bars at the supports is different for the two flights. So they are shown separately.
The second flight BC does not require distributor bars in the landings B and C. This is because the main bars of flights AB and CD will act as distributors. So we need to provide distributor bars for BC in it’s sloping portion only.
It should be noted that the main bars of the two flights AB and CD pass above the main bars of BC. Flight BC is not required to carry the loads from the other flights. But even then it’s bars are given beneath the others. This is because it is always better to give the bars of the shorter span as the bottom most layer.
This completes the analysis and design of the open well staircase. In the next chapter we will discuss about the design of Two way slabs.

PREVIOUS      CONTENTS     NEXT

             Copyright ©2015 limitstatelessons.blogspot.com - All Rights Reserved